Search the Community

Salutare. Am o problema cu al meu calculator. Din cand in cand (banuiala mea e ca atunci cand procesorul este prea incarcat) calculatorul se blocheaza sau apare un ecran albastru cu mult scris pe el. Am schimbat mai toate componentele din el cu exceptia hard discului. Utilizand programul HD Tune Pro am obtinut urmatoarele date (de mai jos) problema e ca nu stiu sa le interpretez. E posibil ca problemele pe care le am sa fie datorate hard-ului ? Multumesc, o seara frumoasa ! HD Tune Pro: Maxtor 6E040L0 Benchmark Test capacity: full Read transfer rate Transfer Rate Minimum : 8.5 MB/s Transfer Rate Maximum : 29.2 MB/s Transfer Rate Average : 27.4 MB/s Access Time : 15.3 ms Burst Rate : 30.8 MB/s CPU Usage : 13.0% HD Tune Pro: Maxtor 6E040L0 Information Firmware version : NAR61EA0 Serial number : E1RJL37E Capacity : 38.5 gB (35.9 GB) Buffer size : 2048 KB Sector size : 512 bytes Standard : ATA/ATAPI-7 Supported mode : UDMA Mode 6 Current mode : UDMA Mode 2 Avergae speed : - Rotation speed : - S.M.A.R.T : yes 48-bit Address : no Read Look-Ahead : yes Write Cache : yes Host Protected Area : yes Device Configuration Overlay : yes Firmware Upgradable : yes Automatic Acoustic Management: yes Power Management : yes Advanced Power Management : yes Interface Power Management : no Power-up in Standby : no Security Mode : yes SCT Tables : no Native Command Queuing (NCQ) : no Trim : no Volume : (C:) Capacity : 14998 MB Free : 12505 MB Usage : 17% File system : NTFS Serial : 40A0-A443 Alignment : 0.5 KB Volume : (D:) Capacity : 21691 MB Free : 16008 MB Usage : 26% File system : NTFS Serial : 54CB-9E85 Alignment : 0.5 KB HD Tune Pro: Maxtor 6E040L0 Health ID Current Worst ThresholdData Status (03) Spin Up Time 222 220 63 7348 ok (04) Start/Stop Count 252 252 0 3857 ok (05) Reallocated Sector Count 251 251 63 13 warning (06) Read Channel Margin 253 253 100 0 ok (07) Seek Error Rate 253 252 0 0 ok (08) Seek Time Performance 251 243 187 33466 ok (09) Power On Hours Count 236 236 0 37512 ok (0A) Spin Retry Count 253 252 157 0 ok (0B) Calibration Retry Count 253 252 223 0 ok (0C) Power Cycle Count 242 242 0 4495 ok (C0) Unsafe Shutdown Count 250 250 0 3399 ok (C1) Load Cycle Count 251 251 0 10154 ok (C2) Temperature 253 253 0 33 ok (C3) Hardware ECC Recovered 253 252 0 1671 ok (C4) Reallocated Event Count 253 253 0 0 ok (C5) Current Pending Sector 253 253 0 0 ok (C6) Offline Uncorrectable 252 252 0 1 ok (C7) Interface CRC Error Count 199 198 0 1 attention (C8) Write Error Rate 253 252 0 0 ok (C9) Soft Read Error Rate 253 252 0 0 ok (CA) Data Address Marker errors 253 252 0 0 ok (CB) Run Out Cancel 253 252 180 0 ok (CC) Soft ECC Correction 253 252 0 0 ok (CD) Thermal Asperity Rate 253 252 0 0 ok (CF) Spin High Current 253 252 0 0 ok (D0) Spin Buzz 253 252 0 0 ok (D1) Offline Seek Performance 187 186 0 0 ok (63) Unknown Attribute 253 253 0 0 ok (64) Unknown Attribute 253 253 0 0 ok (65) Unknown Attribute 253 253 0 0 ok Health Status : warning HD Tune Pro: Maxtor 6E040L0 Error Scan Scanned data : 38 gB Damaged Blocks : 0.0 % Elapsed Time : 24:21