Gabycs94 Posted June 3, 2011 Report Posted June 3, 2011 (edited) Salutare, am si eu o eroare la scriptul pentru crack wireless, am dictionar, dar imi da aceasta eroare dupa ce selectez reteaua wireless , adica 1.root@user:/home/oust/Desktop# bash wiffy.sh[*] wiffy v0.1 (#5)[>] Analyzing: Environment Num | ESSID | BSSID | Protected | Cha | Quality-----|------------------------|-------------------|-----------|-----|--------- 1 | dlink | 1C:BD:B1:52:C1:44 | on (WPA) | | 59/100[~] recan, re[f]resh, e[x]it or select num: 1[>] Configuring: Environment[-] The monitor interface mon0, isn't correct.[>] Restoring: Environment[*] Done! (= Have you... g0tmi1k? Edited June 4, 2011 by Gabycs94 Quote
Oust Posted June 7, 2011 Report Posted June 7, 2011 BUMP !The message you have entered is too short. Please lengthen your message to at least 10 characters. Quote
zeus_2008 Posted June 7, 2011 Report Posted June 7, 2011 pai la ce anume vrei sa folosesti programul? Vrei un program sa afli parole de wireles sau ce anume te intereseaza? Quote
Oust Posted June 8, 2011 Report Posted June 8, 2011 pai la ce anume vrei sa folosesti programul? Vrei un program sa afli parole de wireles sau ce anume te intereseaza?da, sa aflu/"sparg" parole. Quote
Flubber Posted June 8, 2011 Report Posted June 8, 2011 [-] The monitor interface mon0, isn't correct.Da-ne feedback cu un "ifconfig". Asigura-te ca ai placa de retea "up" (ifconfig wlan0 up) si ca este in monitor mode (nu sunt sigur ca este obligatoriu).Vezi si: Problem with ifconfig wlan0 down / ifconfig wlan0 up and airodump-ngLE: Nu uita, verifica daca ai chipset-ul placii de retea compatibil cu aircrack-ng, sunt sigur ca, g0tm1lk se foloseste de suite-ul aircrack. Quote
Oust Posted June 8, 2011 Report Posted June 8, 2011 eth0 Link encap:Ethernet HWaddr 00:c0:9f:bf:56:0a inet addr:192.168.1.134 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::2c0:9fff:febf:560a/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:884093 errors:0 dropped:0 overruns:0 frame:0 TX packets:594987 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1072499854 (1.0 GB) TX bytes:137825075 (137.8 MB) Interrupt:16 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:5842 errors:0 dropped:0 overruns:0 frame:0 TX packets:5842 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:31467907 (31.4 MB) TX bytes:31467907 (31.4 MB) Quote
Flubber Posted June 8, 2011 Report Posted June 8, 2011 Nu este prezenta nicio placa de retea wireless. Ifconfig-ul este generat dupa ce ai datifconfig wlan0 downiwconfig wlan0 mode monitorifconfig wlan0 up?Problema este ca nu se poate atasa de o interfata ce se afla in monitor mode, cel mai probabil se foloseste pentru a face injectii si/sau a realiza 'penetrarea'. Ciudat este faptul ca iti detecteaza reteaua wireless, deci prezenta unei placi de retea wireless trebuia sa rasara la ifconfig. Weird!Incearca si astaifconfig wlan0 downifconfig mon0 downiwconfig mon0 mode monitorifconfig wlan0 upifconfig mon0 upSi apoi ruleaza scriptul. Quote
Oust Posted June 9, 2011 Report Posted June 9, 2011 Ahhh, nu pornisem wireless-u.Uite aici iwconfig dupa ce aprind wifilo no wireless extensions.eth0 no wireless extensions.eth1 IEEE 802.11bg ESSID:off/any Mode:Managed Channel:0 Access Point: Not-Associated Bit Rate:0 kb/s Tx-Power=20 dBm Sensitivity=8/0 Retry limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 Quote
Flubber Posted June 9, 2011 Report Posted June 9, 2011 Ahhh, nu pornisem wireless-u.Uite aici iwconfig dupa ce aprind wifilo no wireless extensions.eth0 no wireless extensions.eth1 IEEE 802.11bg ESSID:off/any Mode:Managed Channel:0 Access Point: Not-Associated Bit Rate:0 kb/s Tx-Power=20 dBm Sensitivity=8/0 Retry limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0Ciudat ca nu ti-o arata "wlan0", ce distro folosesti?OK, m-am uitat peste script si aparent ai nevoie de o placa in monitor mode.Te sfatuiesc sa daibash wiffy.sh --helpIn special trebuie sa ii specifici intai (interfata nu este oligatorie, aparent le detecteaza singur -- tie iti trebuie o interfata in monitor mode -- asigura-te ca ai aircrack suite instalat!) Options: -i --- Internet Interface e.g. wlan0 -t --- Monitor Interface e.g. mon0In cazul tau interfata este eth1. Interfata in monitor mode nu stiu la tine care este.Deasemenea cred ca eth1 trebuie sa fie oprita ca sa vina folosita de airmon-ng (prin intermediul acelui script facut de g0tm1lk), iar asta necesita o interfata in monitor mode necesara pentru a realiza injectie. Quote
adi003user Posted June 9, 2011 Report Posted June 9, 2011 porneste kismet. o sa iti aduca interfata wlan0mon sau mon0 up. ruleaza scriptul dupa Quote
